Skip to content

Sonic Pad - Model.2 - (For 20mm profile)

Advertising
Share
Add to
Make
Advertising
?
Creation quality: 5/5 (1 vote)
Evaluation of on the printability, utility, level of detail, etc.
License
Usages
3D design format
14 files (STL) Close
  • Soporte - Creality Sonic Pad (M2-R2)-2-Brazo.stl
  • Soporte - Creality Sonic Pad (M2-R2)-3-Tornillo.stl
  • Soporte - Creality Sonic Pad (M2-R2)-4-Tuerca.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8A-Fijacion izquierda.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8B-Fijacion derecha.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8D-Arandela 0,25mm.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8D-Arandela 0,50mm.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8D-Arandela 1.50mm.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8D-Arandela 1mm.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8D-Arandela 2mm.stl
  • Soporte - Creality Sonic Pad (M2-R2)-8D-Tuerca.stl
  • Soporte - Creality Sonic Pad (M2-R2-20mm)-1B-Fijacion (Anclaje 20mm).stl
  • Soporte - Creality Sonic Pad (M2-R2-20mm)-7B-Guia cables (Anclaje 20mm).stl
  • Soporte - Creality Sonic Pad (M2-R2-20mm)-7BP-Guia cables plus (2cm ancho).stl

Learn more about the formats
Publication date 2024-03-26 at 19:18
Design number 1882142
alfmar

alfmar

Certified
Issue with this design? Report a problem.

3D printer file info

3D model description

I currently have two models published, each with three variations, check which one best suits your needs, it's a matter of taste:

Model 1

20mm: https://cults3d.emulatorsite.com/en/3d-model/tool/soporte-sonic-pad-modelo-1-para-perfil-20mm

40mm: https://cults3d.emulatorsite.com/en/3d-model/tool/soporte-sonic-pad-modelo-1-para-perfil-40mm

Ender 6: https://cults3d.emulatorsite.com/en/3d-model/tool/soporte-sonic-pad-modelo-1-ender-6

Model 2

20mm: https://cults3d.emulatorsite.com/en/3d-model/tool/soporte-sonic-pad-modelo-2-para-perfil-20mm

40mm: https://cults3d.emulatorsite.com/en/3d-model/tool/soporte-sonic-pad-modelo-2-para-perfil-40mm

Ender 6: https://cults3d.emulatorsite.com/en/3d-model/tool/soporte-sonic-pad-modelo-2-ender-6

Details:

Can be easily used on many printers, it is designed to anchor securely to a 20mm vertical profile.

Its position can be adjusted as required, allowing it to be positioned to the right or left, up, down and screen orientation.

For the union, it will be necessary to remove the legs of the screen and use the same screws, allowing to use up to four fixings of the screen "highly recommended" by adding two screws (M3 * 8). By means of this anchorage, a better fixation is obtained, being the screen fastened in 4 points to the .

This model is designed for s who need to change the viewing angle or position of the screen frequently, with the adjustment work falling on the axes instead of the upper screws of the screen. If you change the pitch position frequently, it will not be necessary to loosen and tighten the nut each time, just keep the locking nut slightly tightened and the screen will be allowed to move without the need to constantly use the nut.

The fixing of the to the printer, allows to hide the screws with some covers or also to do without covers and to use these hollows to mount rings that facilitate the fixation of the cables "very advisable". In this model the cable fixing is included, the covers are not necessary, if you want you can the base and screw cover available in my profile, they look very good.

The robustness of the bracket keeps the screen highly firm during printing, it does not oscillate or change position with the vibrations of the printer. The screen will be firmly anchored, allowing movement or easy removal by pulling out its shaft.

Washers are enclosed to allow a better fixation and movement, it will be necessary to add 1 of 0.50mm in each shaft t, both the fixing and pitching of the screen, in addition it is advisable to include a 1mm washer before the pitch nut. By means of these washers the correct adjustment and movement is completed without component wear.

3D printing settings

It is recommended that it be printed with at least 3 or more layers on walls and a minimum density of 35%.

Categories

Machine tools

Tags

Advertising

Page translated by automatic translation. See the original version.

Would you like to Cults?

You like Cults and you want to help us continue the adventure independently? Please note that we are a small team of 4 people, therefore it is very simple to us to maintain the activity and create future developments. Here are 3 solutions accessible to all:

  • ADVERTISING: Disable your ad blocker.
  • DONATE: Make a donation via Ko-Fi 💜.
  • WORD OF MOUTH: Invite your friends to come, discover the platform and the magnificent 3D files shared by the community!

Sharing and ing on Cults3D guarantees that designs remain in makers community hands! And not in the hands of the 3D printing or software giants who own the competing platforms and exploit the designs for their own commercial interests.

Cults3D is an independent, self-financed site that is not able to any investor or brand. Almost all of the site’s revenues are paid back to the platform’s makers. The content published on the site serves only the interests of its authors and not those of 3D printer brands who also wish to control the 3D modeling market.