23 commentaires

I apologize but unfortunately I wont be separating that particular set.

unfortunate indeed

I do not unfortunately I stopped doing that a long time ago as it wasn't worth keeping my adobe sub for how little I sold them.

I don't take commission for anything. yes I make models for my cults store but that's just so that I can afford to keep doing the hobby. If I took commission I feel like it would become more of a job, and I just want to enjoy the things I like.

Alrighty, thank you

I've just finished the thigh armor, chest plat and shoulder as of last night, I still need to model the arms. so soon

ok its all done and ready now.

If your referring to the update I just sent out. open your back piece and then the new part I listed, it should show you were it goes. unfortunately trying to show how a new part or update to a file works in cults is impossible as I can't share media in a message. if there was only another way to reach out to me like IG or something where I could sent you photos and videos to help, unfortunately cults recently told me I'm not allowed to do that. wink wink

dude that helmet is sick and I'll see what I can do I have a few projects ahead of it.

I wont be home until late, give me some time to get back to you

no worries, i have until sept 1st until the con

So I double checked all the files and they are still in the folder the parts I think your talking about are labeled like this: standard chest armor left back rib plate.stl and standard chest armor right back rib plate.stl not to be confused with the front ones. the part do look very similar but they are not.

i tried fitting those on but they dont line up very well, its the back shoulder blade sections next to the neck piece

I have now triple checked all the files because of this these comments. I didn't find any missing shoulder blade part that you are referring too. additionally in those files I included the .3mf file that can be opened in 3dbuilder on pc and you can view all the parts and resize them if needed. the back consist of the main center part the middle neck area and the two sides on the bottom. I posted my test print holding together all the parts with tape on IG if that helps here: https://www.instagram.com/p/C5cb9EgLbhE/?hl=en&img_index=1 the only thing I can think of is maybe your referring to a cloth part?

my bad i get it now im just a bit stupid lol thank you for the help!!

Not stupid. I get it its a lot of parts, glad you figured it out

I get a lot of request to do all sorts of variants and though I wish I had the time too its slow going sometimes. so I cant say it will be done soon. but maybe in the future. no promises.

That's totally fine. Like I said, you already have the SA-04 pieces I want. :)

sorry I don't take commissions. it does look very cool though, I haven't seen it in the game yet if I unlock it I might do it anyway.

it hasn't been released yet, I think it's coming in next months warbond. Thanks anyway :)

I use the cults site because one of the benefits is they facilitate that for me this is why they take a percentage of my sales. so unfortunately I prefer that all business stays through the site.

I appreciate the kind words, also you don't need to spent 1500 for a decent printer to print any of the things I make. I've been using a Neptune 3 plus which is like 280 right now and Bambu A1 for smaller parts, to test my models with. also I'm just one guy doing this between life stuff, lots of people ask me to make all sorts of parts from the game I can only do so much. so bare with me I'm not shoving anything under a rug. if someone doesn't get a reply its just that I'm busy which is a good thing.

This is referring to the drone master helmet, sorry

unfortunately other projects have priority at this time. But your more than welcome to slice it using the bambu studio it has a very nice feature for slicing.

right now it does not as its still new and growing, however depending on how the patron grows it could change. for now it gives you a license to sell physical prints you make from them, as well as access to the monthly reward, early releases, patron only models, and suggestions.

yes blender

How do you get your helmet looking so smooth? It Looks like it the polys are non existent.

There is now a .3mf file included its titled "All parts use this file to understand how they go together.3mf" open that file up in something like 3d builder on your pc and it will show you all the parts and how they go together.

So the Glue I use for putting together 3d prints together is Loctite superglue however its just to line up the parts and hold them in place long enough for me to plastic weld the inside, or the side that people wont see. then if there are any small gaps on the outside I will use some baking soda or baby powder to fill in the small gaps and then use more of the super glue and I let it soak in and dry then I can go about sanding my project. also just in case "plastic welding" can be done a few ways friction from a Dremel. 3d printing glowsticks sized sticks for your glue gun, or using a wood burning or soldering tool and extra filament to melt it against the seems. there is also a tool that melts small metal staples into plastic to repair or connect parts. however I typically with do the wood burning tool and extra pla as my main option. hope that helps

That’s awesome thank you so much! I can’t wait! this is my first attempt! I want to do the armor next! so cool you added the skulls!!!!

I've made a video just for you on my instagram @ alwaystimstime here is the direct link to it https://www.instagram.com/p/C5MHq7-pYSn/?hl=en

commercial license available via Patreon

I don't slice my files up because everyone has different preferences and there are many different size printers out there. however the Bambu studio software that your p1s uses does give you the ability to slice up your model into easy to manage parts that you want. also you can use the free program windows 3d builder to slice your model as you see fit, that is if you choose not to use the Bambu studio software. unfortunately this is not a valid reason for a refund. you already now own the file.

It's made from ya ya hans hex cosplay fabric it was the left overs from the elite project. its just a generic circle pattern nothing fancy