67 commentaires

Hello is there an xmodel for the Star Spinner? Thank you

Purchased the singing light bulb and trees. How about doing a singing snowman?

Hello! Do you have the xlights model for the tombstone? Greatly appreciated! Thank you!

Hello, could you send me the xlights model, I would be very grateful

Do you have a xlight model file and a wiring diagram for the snowflake

I would like to know if its possible for you to make a cross the same size as the tombstone. by the way the tombstones are printing out great.

Hi, do you have an xmodel for the pixel tombstone? https://cults3d.emulatorsite.com/en/3d-model/home/ws2811-pixel-tombstone
Thanks!

Hiya , on the fan arch i keep having issues with arch 4 and 16,17 ,18 . all other pieces print fine. those say i have a cantilever overhang. all slicers do the same . i tried several things like move around , infill etc. when printing it prints a few small bits here and there and then goes next layer and makes a mess. tried it on a ender 3 max neo , a kingroon klp1 and a infimech tx printer. tried pla and petg. temp settings higher and lower. cura , orca slicer both give the same.. could you please fix them and notify me as i am printing the fan arches for my xmass setup.

do you have an x model for the guitar?

Hello. Do you have the xmodel for the ws2811 Spider?

Thanks,
Chris

howdy. do you have the xmodel for the WS2811 STAR SPINNER.. I am going to use this as a captain america shield for my 12ft skelly.. Thank you

Can you send me the Xlights model for ws2811 24inch spinner?
Thanks
[email protected]

Hi. do you have an xLights model for olaf or your snowflakes?

Where can I find the Xlights model for the Olaf face?

Hi,
I just wanted to see if the xlights model is in the zip file when we the Olaf. Thanks

Hello Viper ik heb een vraagje hoe importeer ik jouw modellen in xlights kan dat nergens vinden.

I cannot find the xlights models for the singing ghost or the spider in the Facebook group. Can you tell me where I can find them?

Is there a simple way you can share to getting the holly/bat image in xLights? I am a beginner.

Do you have a Xmodel for your 30in Spinner. I d/l it a while back and printed yesterday, but realized I don't have a model for it to bring into xlights

Bonjour, est ce vous avez egalement le fichier xmodel pour permettre le cablage correct et eventuellement avoir des « submodels »
Merci

Can i get the xlights model for the WS2811 PIXEL TALKING PUMPKIN please... i see youv mentioned messaging you on fb to others however idk how to you there

hi, im just enquiring about the 16 inch snowflake that can be ed to other flakes. do you know what model i need to in xlights to use this flake as i dont seem to be able to find it. i ed the flake a while ago and printed them out, i think they look really good ed together.
thanks Paul

Printed the star for the mini tree. Is it intentional that some pixel holes are bigger than the others? Basically, the center pixel is correct. If I go straight out from the center to one of the tips, those 3 (in line to tip of star) are correct. But the others are slightly bigger and causes the pixels to go right through.

Basically, the 5 the make the ring around the center pixel, the 5 on the corners of the outer ring of the main pentagon, and the 2 at the base of each point (2 closest to the main pentagon in the tips) are slightly larger than the others. I can make it work with hot glue but would be a lot quicker putting together if they were the right size. Just want to make sure I'm not missing a reason for that or if it's something on my end.

Hello - does the WS2811 SINGING ELF come with an XModel?

Hey man, I ed your spider print and I'm loving them. By chance, do you also have a pumpkin like this or know where I could get one? https://prnt.sc/ETG_zehF6f3v