50 commentaires

Hey, i have no plans on making this
(i dont know what is it too though...)

https://www.facebook.com/CrystalofAtlan.TH/posts/-berseker-%E0%B8%94%E0%B8%B5%E0%B9%84%E0%B8%8B%E0%B8%99%E0%B9%8C%E0%B9%82%E0%B8%8A%E0%B8%A7%E0%B9%8C%E0%B9%80%E0%B8%84%E0%B8%AA-berserker-%E0%B8%84%E0%B8%B7%E0%B8%AD%E0%B8%A8%E0%B8%B9%E0%B8%99%E0%B8%A2%E0%B9%8C%E0%B8%A3%E0%B8%A7%E0%B8%A1%E0%B9%81%E0%B8%AB%E0%B9%88%E0%B8%87%E0%B8%84%E0%B8%A7%E0%B8%B2%E0%B8%A1%E0%B9%82%E0%B8%81%E0%B8%A5%E0%B8%B2%E0%B8%AB%E0%B8%A5%E0%B9%81%E0%B8%A5%E0%B8%B0%E0%B8%9E%E0%B8%A5%E0%B8%B1%E0%B8%87%E0%B8%AD%E0%B8%B1%E0%B8%99%E0%B8%94%E0%B8%B8%E0%B8%94%E0%B8%B1%E0%B8%99-%E0%B8%82%E0%B8%B1%E0%B8%9A%E0%B9%80%E0%B8%84/122130506474671720/

Hello, i will.

Im finishing the back part of the leg shin armor, i will also finish the sword and will be making the front chest part and prob the side shoulder big part next week.

Hello

To clarify, the sword would be physically attached using some kind of tape/strap/rope, right? I'm not sure if magnets alone would its weight (500g)+.

But about the pins, they are 15mm x 10mm x 30mm (smaller version) and 15mm x 50 mm x 10mm (larger version) (both measurements are for the space to fit, the pin models are already approximately 5% smaller for a better fit.

But also, if you want, I can make the spaces to fit the magnets wherever you think is best, as well as the specific size you want.

I was actually planning to use two magnets that are rated to hold around 12kg each, so I hope those alone should be able to hold the sword haha. But yes, it would definitely be nice if you were able to make spaces for the magnets in that case.

I'll send another message once the magnets have arrived so I can measure properly and when I've actually purchased the files for the sword :)

Hello, i might, but depeds more on the project/model

I was thinking about flame reaver (from star rail) sword, boots and gloves

also mask

okay, i will see to do this week, i might be able to

Okay, thanks

Hello, i have ed the mask, legs and shoes, and arms and hands armor. The sword i think might be ready till the end of the week,

Also, do you have any preference on the diameter size of the inside hole for a rod/metal/pipe?

Hi. I already got mask and legs( can you also include back part?). I don't see arms and hands armor tho. I think 10mm diameter size would be good but can you make it 10.2mm or something like because when I printed capitano sword the hole was a little bit too small for 10mm rod. If it is possible can you also make it so I can fit leds inside the sword. Thanks

You didn't find the Hands and armor files or something?

And yes, i will make the hole with a little more tolerance, the capitano sword was an early project and didnt had paid attention with some details :x
About the leds i will have to see how its going to look the end model. The model of his sword is just a nightmare itself caus of the floating parts.

Yea the design of his sword is hard to project in real life. I found the gloves dunno why they weren't appearing on your profile i had to serach for them. Will you be willing to do the rest of arms armor and also back of legs? It doesn't matter when you do it tho just set the price higher cus i feel like I'm ripping you off

Ah also about the mask are those things not blocking line of sight?

Hahaha no problem, im setting the values at open price so people can tip the amount they think is valid (really appreciate but if not, no problem too!)

About the mask, it may block some of the line of sight, but not all (for all i see in the model, i havent print it). But in any case, you can move a bit up/down so it blocks less.

For the rest of the armor for the arms, im thinking about only doing the shoulder big piece, but next week. The rest is way to plain (looks more like a thicker golden frabric around holding the armor in place) to make it 3d print, considering it should fit around an arm (something way too organic and variable among people).

The back of the legs i might do it. Its has the same problem the arms have, but it does have some geometry so i might try.

Hey, i will edit here and update the model for you.

Just to make sure, the slot on the crystals, is in its base right? or do you need the body as much hollow too?

The part next to the blade if possible, would be great if you could make it so it's like a box that opens to fit in the battery and wires! Doesnt need a mechanism, I plan on using magnets to keep it shut, thank you.

Hey, i have made the changes, dont know if the result is as accurate as you need but here is a image showing kind how it goes:

https://ibb.co/65SPLjw
https://ibb.co/1f2gTgCv

If this is okay, i will save and for you re the files

Here is another version, with the box layed down, so it consumes less of the midde part in exchange of geting the crystals on both sides (no visible hole)

https://ibb.co/BSQRW5p

Amazing, you work so fast! I'll have time to print on the weekend, thanks a lot!

(took more time than i had in mind, weekend was tuff for me)

but glad its okay, i will put in a folder with both options and you can choose the best for you

Done, you can re it and will be on the new folder.

Note that "Part 3" has 2 versions, the number 1 will use the new crystal version, while the second version of part 3 will still use the old version the side crystals.

Hi there, i will update the files to have the models in single part as you request, give me a few minutes and i will reply here again when ready

you are the best, I'm already starting the prints ty!

Hey, i have updated the parts sliced to single model format. The files have a "Complete" on the end.

I added a headband with attatch slots to the horns too, but will still teste to see how it sits on the head.

If you find any errors or have any suggestion to improve the models or the use of it, feel free to reply
:3

Also, just added the back of her belt too that was missing.

Hello, i have them on my list, prob till the end of the week or soon

Amazing!!

Hey, i have finished and posted the parts;;

Awesome thank you! Do you think you might also be able to do the big pink X that goes over her chest as a separate piece?

That Butterfly/X right?

you think that is better to do all flat and then bend it, or make it bend already?

Yes that one! Either way can work, it might print better flat but do what’s easiest for you and I can make either one work :)

Thank you so much for the reply,

im finishing some other files first, but probably making them as soon as possible then.

Hey, just ed most of his armor now. Tomorrow will post the rest that is missing (his leg spikes and his shoes wings holder)

YOU'RE THE BEST!!! thank you so much!!!

It all looks perfect!!

Hey, thank you.

Not sure if i understood exactly the part you meant,... but right now im a bit busy with oder projects, so dont know when i might be able to make those..

Totally understand, if you do find some time please drop me a message and I'll show you what I'm talking about!

Hello, i have them on my list to do, probably next week

Ola

Eu pretendo sim, nao comece aindai/nao tenho previsao pra ficarem prontos, mas acredito que logo logo devo fazer;
Muito obrigado pelo tbm :3

Hello,

The models do not include the pipe/rod parts. It is necessary to purchase a wooden rod(dowel)/plastic pipe to use as base. The parts have already build-in space for the fitting of the tubes, so each model have specified the size of is hole.

If you have trouble finding a wooden cane/dowel in the right size, me and i can edit the files to better fit the size you have

Hello,

i am planning, but i have other projects first and the references for his weapon so far seem a bit hard to get all the details and so maybe when he is out, or a bit before..

Hey, thank you for the

For the heating, this part is already thin and malable, so a bit of heat is enough to bend it. the key is to heat it all and cold it in the curved place. you dont have to reach high tempeture for it too.

So i suggest you put it in the oven for a few minutes, BUT THE OVEN BUT BE MINIMUN TEMPETURE, like, 50 celcius or less or the equivalent for the measure you use. you really dont need to be that hot, only to warm so it can cold in the new format.

if this still too confused, let me know and i will try to be more clear ''

Thank you so much for the fast response! I will try the oven out, thanks again!

Hello, thank you so so much for this comment, i really try my best to add asmuch details as possible while keep the most optimal for 3d printing''

Will look foward too see it finished!'

Hello, mostly all parts actually fit a ender printer (220 x 220 x 250) size. And in this case of the hammer, i have been requested already to slice the bigger parts to fit smaller printer, so there is a folder included that is named "New version smaller".

Perfect, thank you so much

hello again, but to get the complete hammer with a small printer (the ender 3 pro) I have to print the files from the 20 mm rod and new version smaller folder right? but how come by ing these folders the pieces are 13 and instead in the jayce hammer folder they are 19? sorry but I am a beginner and I would need help; I also intended to resize them because they fit in just fine and give some problems in the slicer

Hello

So, the files come as follows:

"Jayce Arcane survivor bundle.zip" This is the main folder. It has all the files, all normal and no modification (they should still be able to print in a ender3, but might not be able to upscale, or might be on the edge of limit of printing it.

"28mm rod parts.zip" this zip contains a second version of the normal files, but only the ones where the main wooden/pipe rod would go through, in this case a bigger version, for a 28mm diameter rod pipe or dowel.

"New version smaller.zip" contains the same files as the main folder, but the bigger parts are sliced even more so it becomes smaller and easier to print. The name of the files in the folder follows the same name of the files that should be replaced in the original, example:

In the original, there is a "Jayce Arcane survivor hammer side 2 4.stl" and in the smaller part its the same as the two parts: "Jayce Arcane survivor hammer side 2 4.1.stl" and "Jayce Arcane survivor hammer side 2 4.2.stl"

If you still find this a bit dificult to understand, please me in instagram linked so i can help you better.

Hey, the image link you posted is just the site, there is no image there...

But i looked here in his model, and both of these seem to be more of a fabric/leather and i personanaly think that 3d print these might no be the best option. His left shoulder goes all the way to his back (https://ibb.co/zT24RjFc) and might need some movement and flow, as it holds the cape too. His right hand guard (https://ibb.co/fWYbfN8) looks like it needs some movement too or it would leave the arm to stiffy.

I can plan to do some of the detail of these parts though..

Hey, about the ammount of fillament, using the specs i use that are:

5%~10% infill
3 walls
3/4 layers of bottom and top

the total would be around 2kg and 600grams, but you can deff make this number smaller using other specs in some specific parts..

Thanks! Very helpful!!!

Hey, thank you for the comment~~

About the front armor and the shoulder, What parts are exactly? i will add and image for reference here
https://ibb.co/zTx8g7MT

Hello, thank you for reaching out.

Can you elaborate a bit what you mean in "how to print"? Like, do need help positioning on the slicer, or the best specs recommended for printing, or anything else..?

And for the assemble, its really straightforward, once you have all the parts printed, its really intuitive to assemble, you can use the images in the post as reference for better guide too, but there should not be any dificulties.

If you need any specifc help or find any trouble let me know in more details.

Hey, im will be working on him soon, prob till the end of the week/weekend. Im finishing Starlord from marvel rivals, then will be doing some ZZZ.

i will be doing his accessories and his shoulder armor;;

Thank you so much! I'll be waiting patiently. Please take good care of yourself. 💙✨

Hey, sorry im late D:

But will be ing his acc's today and tomorrow~~

Hello, (are you brazilian?)

I think you are talking about the Mavuika's weapon right? It does not have slots for LED, and i accually never have done one with it, so i dont know the right specs for it...

nvm lol i realized i can just mirror it myself haha

Yeah, the 3 part is one side (left), the right side shoulder is just a mirrored version of it. in the slicer itself can be done, but if you have trouble let me know and i will do it myself to include in the files