14 commentaires

Hi Peter.. They're all raw metal I guess. Like almost every machine in Matrix ;) Thank you for ing it and have a wonderfull day.

I'm sorry you have such troubles.You'll be refunded. I assume you followed my recommended print settings but still, this is difficult build which requires well calibrated printer. If those requirements are fullfilled you shouldn't have problems printing it.

Well, that is up to you. Orca slicer or Prusa slicer can separate mesh into two parts for you. I wouldn't do that just because it will leave a seam which I don't want.

I saw that the model has some lines and stuff, so to not make seams I thought abt separating the parts of the model that have these lines and then ing them together… idk how well that would work on resistance tho.

I thought about that so much when I was deg and modeling it.My goal was to have a build as easy as possible considering how detailed sentinel is. Separating model by following lines would make the build and also modeling so much harder.Having the body as single piece is one of those better decisions. I've also tried a lot of orientions of the body before releasing this model and i think/believe this one is the best you can get. I apologize but for me it would be time i'm not willing to invest. I am sorry Febodez 😿

Hi, sounds good. Can't promis when but i will. Stay tuned please.

Oh dear... i'am sorry for that. Which model of the hand did you print ? Preed or the one without s ?
There could be couple of issues. One - did you properly washed the parts before curing ? Second - did you calibrate exposure times for your resin ?
Do those ts break due to fused resin inside them ? Can you send me a closeup photo of that broken t, please ?

I'm using the resin version and iv done both in various configurations ed in 2 different resins on 3 different exposure times and stock, and uned where my system did the s and same setting combos and me doing the s as well; resulting on all of them being fused on the inside in some degree or other. Also, reduced the print layers to .010 to make sure the curves got the clearance and still has some parts that stick together, but iv seen an improvement. As in, more of the hinges come out as cleaner prints but still end up fused.. Always on the bottoms of the hinges.. (always clean the crap out of them and none have made it to the cure part, always break on cleaning...).

I love this kit and a heat gun made my life a lot easier when assembling the tentacles. Also, could you please make a dish version of the hand for this kit?

Yes. Someone asked me to do it already. Can't promis when but i certainly will make it. Stay tuned, please.

Kamil, that is so strange. Resin version has quite big tolerances. When you break my s on preed models than hands are actually pretty loose. There must be something else.
I've printed sentinel with two different resin brands. Difference between exposure time after calibration was 1.1 seconds. First resin was calibrated to 2.7 second exp.time and the other one needed 1.6 seconds. Resulting prints of the sentinel were exactly the same in of clearances in hinge ts.

Yes, I agree this is puzzling to me as well. I did a print over night again with 3 different types, your ed then light s and then medium. Sliced at .0100 with a 3 sec exposure on Abs like pro V2 from Anycubic, and each has a different problem but ultimately all are fused at the bases of the ts. I went over your file as well and you do have plenty of tolerances,and it should all work but something is screwy and I'm super frustrated. I'm even going to replace my fep film and try printing it either in high speed or standard to see if something softer with more give will do better.. Would you be able to share your settings for the resins you are using ill try get them and run a test to see if its me or my settings.

After curing. I coloured everything with carbon powder and Eyes are printed on FDM already in red, because i don't have red resin ;)

Aliexpress

Did you see my videos? I'm cutting those fingers with exacto knife into four separate fingers. That is the price for not having to much s....

https://youtu.be/leVyyoRH96M?t=94

Cutting should go pretty easy. If not, try to decrease flow rate 3% down when printing, please.

Hello. This is (unfortunately for you) completely my impression of this creature. So they won't be compatible. I am sorry 😔

Thank you. I really appreciate your praise ❤️

dude make this price at least 5x. it's so worth it.

Hi Nandofabio. I'am so sorry but I've no time for custom designs. Those dices are the only ones i will list in my creations. Kind regards jb.