The Dr Pepper with the Bow! Sorry 😂
- 0 j’aimes
👋 Bonjour à tous ! Ce fil de discussion est public, alors restons gentils et respectueux. Pas de publicité, de spam ou de choses désagréables !
🇺🇸 Pays du membre : États-Unis
🌐 Langue préférée du membre : Anglais. Vous pouvez traduire en ligne via DeepL.
💡 Vous faites référence à un modèle en particulier ? Ajoutez le lien, le titre ou le numéro du modèle.
🖼️ Vous souhaitez publier des photos ? Utilisez un hébergeur gratuit comme ImgBB et collez les liens dans le message.
✍️ Astuces de rédaction : Utilisez le format Markdown pour structurer vos textes et les rendre plus lisible
Écrivez votre message :
14 commentaires
No worries! Change you Z-axis height in settings to 1.75 instead of 1.4. Make sure you don't have it set to "uniform scale" so it only changes the height and not the X or Y axis
- 0 j’aimes
Hi there! Love this one but the wall is kind of short and the mold tears when I am pulling it.
- 0 j’aimes
Hi there! Which mold are you referring to?
- 0 j’aimes
Hi, thank you for your recent s from KischooksKreations. If you have any questions please feel free to me. Happy printing.
- 0 j’aimes
Hello! Would you be able to create the 1" square blank holder with 6 slots instead of 5? I also purchased the stand-up version with 6 slots but would love to have the other version that can showcase 2 sides of the bank, but my blanks are always in sets of 6. Thanks!
- 0 j’aimes
I believe that was the design that had 5 slots because of its width and the width of my print bed. I will go back into my design and see if i might be able to adjust it to make 6 work.
- 0 j’aimes
Ah that makes sense. No worries, let me know if it works out!
- 0 j’aimes
I just played with it a bit. I had to square off the outter edges a bit to gain space. But I did manage to gain enough space to add one more space. I'm running a test print now.
- 0 j’aimes
Hello I have a few that I would like converted to stl. Can I have your email to send images please?
- 0 j’aimes
Please...can you respond to me about the North Pole mold?????
- 0 j’aimes
Please! I need a response from you.
- 0 j’aimes
Hi there! Sorry, my response time was delayed as I was out of state on vacation. To make sure the finer details are printing correctly, try slowing the print speed down and checking your layer height/width.
- 0 j’aimes
Can you please help me with the love you to the north pole and back?
- 0 j’aimes
Please I need help with the north pile one. My comments are below. It's not printing the edges of the candy canes or the y in you.
- 0 j’aimes
I bought the love you to the north pole and back. I've printed it twice and both times it's not filling in the outlines of the 2 candy canes or the bottom of the Y of the word YOU.
- 0 j’aimes
This is beautiful. Can you make a flat keychain with this design?
- 0 j’aimes
Hi there! Which design were you inquiring about?
- 0 j’aimes
And...I love that you made a convex version. My customers seem to like those!
- 1 j’aime
Thank you so much! I always use air to get the molds out, but this one didn't work. The tab was too thin.
- 0 j’aimes
Hi...I ordered and printed the Wild Things On Board mold. Printed great but when I pulled the silicone the tab broke easily and I had to dig it out. Is there any way you can make the tab thicker and wider please?
- 0 j’aimes
Hi friend! I've updated it with a new pull tab as well as included a second STL with convex wording. Hope this helps! As a side note: if you ever have trouble removing silicone molds from the housing, use an air compressor with the smallest needle attachment and blast some air down into the mold. It should pop right out! :)
- 0 j’aimes
Is there any way you would create another DR. PEPPER CAR Freshie mold housing without the bow?
Actually, I’d you could put it on a can, that would even be better.
The Dr. Pepper can is now ed :)