AutoSwap BambuLab A1 Plate Changer Upgrade Kit V1.3 Final

Hello, thank you very much. Yes, the magnets on the back side can cause problems, unfortunately. I added rubber for this, it works much better when rubber is used instead of magnets. If you are printing ABS prints in your bambulab, Neodymium magnets lose their power after 80 degrees of temperature, unfortunately. Instead, it is necessary to use Samarium-Cobalt magnet or much more easily rubber will work.
I thank you very much for producing an idea to work on the project. I will try it.
If the neodymium magnets lose their function, don't forget to put a tire on them. thank you very much again.

Part of the problem is that the magnets are spec'd based on size and not pull strength. I had to get them through Amazon to find the correct size. The top magnets I changed to 3mm thickness, they just fit, and no more issues. I don't print using ABS so didn't have any available, so the ABS parts are printed in PETG at the moment. I have a roll of ABS that I am drying now to reprint those parts.

Thank you. I'm very happy. Again, you can write to me if you have any questions.

Hello. there are no missing model parts in the project. please do not give false information. there is no free beta project of this project or similar, I think you have confused it with something else. I cannot have such an obligation about s. It is up to you to use the s as you wish, but I have attached the necessary documents for the s and if you proceed according to the images and information in the document, you can print without any problems. I am constantly responding to emails. I help you with everything and I tried to help you too. If you cannot remove the s from the magnet slots, the filament you are using is problematic, I guess I cannot be the cause of this... I think you are doing it wrong. I tried to help you via e-mail but I failed. I think you are using 3d print for the first time and you are a beginner. I refund your fee. just ask for it. thanks.

I refunded your fee.

I use honeycomb as a filling pattern and I told you that I only use honeycomb. I said you can use honeycomb if you want. I didn't see anything wrong here :S

I know you are using translation in both directions so let me try to explain it again.

When you sell a project, you should take care of its quality. If parts need certain settings like s, brims, non-default number of walls, infill type, or percentage, then you should set this in the project properties. Even designers of free projects do that. Instead, you just use defaults and then provide SOME information in plate names. Then I need to uncover rest via numerous emails. And some of that is wrong, for example you are telling that I can use honeycomb while you cannot use honeycomb with 100% infill. I've already printed plenty of big and complex projects and only yours is giving me problems with some parts. For example Swapmod for A1 Mini turned out great. Big dual AMS sets or Mini AMS Lite as well. Yours has been tested with different filaments from different vendors, two best plates (Supertack and Frostbite) and two different printers - A1 and P1S and still some parts print with issues.
And yes, there are free alternatives on English-speaking MakerWorld plus some extras on Chinese version.

Yes i use translation i hope you understand me.
you can't use honeycomb at 100% fill Bambustudio doesn't allow it. i only said that i use honeycomb in general, i mean that i use honeycomb when you use a fill below 100%. i didn't say that it's mandatory or something you have to have. i didn't say that you have to do it. i just said that i personally use honeycomb. i don't understand how you perceive it as an obligation. i repeat that there are no free alternatives for the a1 model in MakerWorld. please don't insist on this. please check it thoroughly. I have been working with 3d printer for 15 years and deg models. if you have difficulty in putting , I cannot be responsible for this. you asked for help on this issue and I created information for you visually and in writing, but you still could not print. please check your devices and filament. Some people use PETG between the s in PLA prints to print smoothly. so I don't have to add the s into the project necessarily and Cults3d doesn't require it. I refunded your fee and I am sorry that you failed in the project. I wish you success in free models.

Not: I cannot correct your insistence on giving false information. if you have a problem please let's talk via email. the topic has become very long and out of context.

Hi thanks. I have now added it as a 3MF file. but if you are going to modify it for yourself, I can help you if you me via e-mail.

Thank's I'm going to try it ! No start printing parts :-)

Now not No * -_-

Hello, you are very right about this, I added extra rubber to that part in the last update. Plate temperature causes neodymium magnets to lose power. neodymium magnets start to lose power after 70 degrees. unfortunately, a larger magnet will not solve the problem. Instead, installing Samarium-Cobalt (SmCo) magnets will solve the problem, but it is very difficult to find Samarium-Cobalt (SmCo) magnets. for this reason, I made a package tire reinforcement, which is easier. now I am using it in 4 devices and it works without any problems. yet I continue to research.

what are you referring to with the package tie right now im using one of those felt stickers you put on the bottom of stools to limit the downward travel

i released a new update on sunday. i shot a reinstallation video. the new update has no significant changes but you can do the part where i added the package tire.
https://www.youtube.com/watch?v=Z8j-sDm8pRI&t=256s
i show it at 15:25 minutes.

i didn't understand the felt stickers. can you send me a photo. i am using translation, so i think the translation is causing the misunderstanding.

is there a location where I can private message you?

also I really like the addition of the other "arm on the front my machine is pretty wobbly than k you for staying up to date!

Thank you:)
[email protected]
You can write to me for any suggestions or .

Would be great if you make a discord server where we can all chat

:) very good idea but I use deepl translation :)

Discord is forbidden in my country :)

Ahh that sucks, where are you from ?

I am in Turkiye.

Hello, I think there is too much in the rear module 3-4-5-6 parts. I thought this way to be colorful, but unfortunately there is too much as you said. With a new update this weekend, I am organizing these parts to be printed without .
I am preparing an installation video again and an installation pdf file.
Thanks again.

Thank you, that would be great!

ya se podran imprimir sin soporte??? deseo comprarlo, solo quiero estar seguro que funcione bien :) felicidades por tu trabajo

Hello. I am constantly developing with the mails from you. now the final version is very stable. now I am constantly printing with my 4 devices.

ok, provaré con una. pienso que esta genial. actualmente tengo 10 a1 y me encantaria funcionaran de esta manera :)

Hello. Final files are sent to print via bambustudio. this is actually possible.

Hello m3x15 screws for the bottom of the heater plate. if m3x16 mm does not fit, if you send me an e-mail, I can edit the model file and send it. or if you fit a tiny gasket, there will be no problem.

Do you have available some m3x16screws to test it out ? I don't want to print it again

Oh I also notice you are using other type m3 screw, can I use hex screw ?

Hola, lamentablemente no tengo tornillos M3x16, creo que hay 15 en mi país, pero los tornillos m3X16 no causarán problemas.
Si usted tiene tornillos hexagonales, funcionará y no habrá ningún problema.
Si hay algún problema, puede enviarme un correo electrónico con fotos.

Hello, thank you very much for your purchase. of course, please do not hesitate to send me an e-mail for any problems or requests. I am working hard on this project and I am with you until it is perfect. thank you very much again.

Unfortunately prusa models are not sold in my country :(

Hello, I added the total dimensions into the catalog images. thank you very much for this information.

oh snap also what 0.XXmm fishing line should we get?

Hello, thanks a lot for the purchase, yes it is an application like swapmod but to work on your own local computer. I finished the software and now I am in the testing and video phase. I will add it to the project in 2 days.

Awesome! had to order magnets from temu also same as you mentioned ^^ just in case

also buildplate*

Hello, you can send your prints in order via BambuStudio. I am deg a website where you will combine your 3MF files for multiple prints, I will activate it in 2 days and I will publish a video. thanks in advance.

Great work! I am excited :)

Hello, you can send your prints in order via BambuStudio. I am deg a website where you will combine your 3MF files for multiple prints, I will activate it in 2 days and I will publish a video. thanks in advance.

Hello, I bought it from Temu, the price was very reasonable. thickness and dimensions were the same as the original
Link: t.ly/eyFhp

Hello, you do not need to re-purchase for a second version. I will send you notifications via Cult3D when we update and you will be able to continue ing for free.

awesome, thanks!

Yes, a A1 Mini version would be very nice to have as well.

Thank you very much. it was made as swapmod for a1 mini but I am thinking of buying a1 mini and creality. then I will do it immediately. trying to decide which model I should make creality:)

Hello, there is the necessary gcode in the files. With a small revision in bamboo studio, you will have activated AutoSwap mode.

Hello, thank you very much, if you have a problem, you can send me an e-mail. it is important that you print the model with Rear Bottom 2 and 3 in the project as PETG or ABS. it will be very useful in your work.

Thank you very much for your purchase. I have added 3d printing details. your suggestions and ideas are very important to me. thank you.

Thank you very much:) I will continue to improve and add to it.