BubblePlanter avec gouttière cachée

BubblePlanter

Elevate your plants with the BubblePlanter! This innovative design features fine vertical fins that create a mesmerizing bubble effect.

Features

• Free: The round disk needs to be printed beforehand and will be inserted mid-print, eliminating the need for and delivering a clean finish.
• Fine Vertical Fins: Sleek, vertical fins enhance the aesthetic and add structural strength.
• Bubble Design: Inspired by the elegance of bubbles, this design brings a modern twist to traditional planters.
• Optimized for 3D Printing: Engineered to print without structures, saving time and filament while ensuring a cleaner finish.
• Enhanced Drainage: Strategically placed holes allow excess water to escape, promoting healthier plant growth.

Dimensions

• Planter Diameter: Approximately 120mm (4.7 inches) wide (scalable to suit your needs).
• Planter Height: Approximately 100mm (3.9 inches) high.

Print Settings for BubblePlanter

IMPORTANT: Add a pause to the print at a layer height of 25.2mm (Layer 126) so you can insert the round disk.

Quality
- Layer Height: 0.2mm
- Wall Generator: Arachne
- Order of Walls: Outer / Inner

Strength
- Walls: 2
- Top Shell Layers: 1
- Bottom Shell Layers: 3
- Infill: 10% (Gyroid)

Speed
- Print Speed: 150mm/s for outer walls / 250mm/s for inner walls (adjust as needed based on your printer).
- Slow Down for Overhangs: Uncheck this box to maintain consistent layertime over the disk.
- Over 100% Wall (not Bridge): 250mm/s
- Bridge: 250mm/s

Print Settings for Shelf and Driptray

Quality
- Layer Height: 0.2mm

Strength
- Walls: 2
- Top Shell Layers: 3
- Bottom Shell Layers: 3
- Infill: 10% (Gyroid)

Filament Recommendations

• 3Dhojor Crystal Rainbow Glacier PLA: Check it out here

Print Time and Filament Usage

• Print Time: Approximately 12 hours (depending on your slicer settings and printer speed).
• Filament Needed: Approximately 280g.

Assembly Notes

• Print the round disk first.
• Note: The disk/shelf is designed 0.4mm smaller in both height and width to ensure an easy, snug fit.
• Add a layer pause at 25.2mm (Layer 126) to insert the round disk.

Ideal Use

Perfect for showcasing succulents, small flowers, or herbs. The BubblePlanter makes a striking addition to any home, office, or garden space.

---

License

🔒 Personal use only.

Commercial use requires a license via our Commercial Tier on Thangs:

👉 LeHaDesign on Thangs

---

Added Files Documentation

• 1_12cmPot_Bubble_SHELF.3mf: PRINT THIS FIRST! Bambustudio 3MF File, Round Disk/Shelf with correct settings, ready to print.
• 1_12cmPot_Bubble_SHELF.stl: PRINT THIS FIRST! STL File Round Disk/Shelf, you need to slice it yourself.
• 2_12cmPot_Bubble_DRIPTRAY.3mf: Twistlock DripTray Bambustudio 3MF File, with correct settings, ready to print.
• 2_12cmPot_Bubble_DRIPTRAY.stl: Twistlock DripTray STL File, you need to slice it yourself.
• 3_12cmPot_Bubble_MAINBODY.3mf: Planter (add a pause at 25.2mm to insert the Shelf/Disk) Bambustudio 3MF File, with correct settings, ready to print.
• 3_12cmPot_Bubble_MAINBODY.stl: Planter (add a pause at 25.2mm to insert the Shelf/Disk) STL File, you need to slice it yourself.
• 12cmPot_Bubble v8.step: STEP File, if you want to change some tolerances.

Print Settings for BubblePlanter

IMPORTANT: Add a pause to the print at a layer height of 25.2mm (Layer 126) so you can insert the round disk.

Quality

Layer Height: 0.2mm
Wall Generator: Arachne
Order of Walls: Outer / Inner

Strength

Walls: 2
Top Shell Layers: 1
Bottom Shell Layers: 3
Infill: 10% (Gyroid)

Speed

Print Speed: 150mm/s for outer walls / 250mm/s for inner walls (adjust as needed based on your printer).
Slow Down for Overhangs: Uncheck this box to maintain consistent layertime over the disk.
Over 100% Wall (not Bridge): 250mm/s
Bridge: 250mm/s

Print Settings for Shelf and Driptray

Quality

Layer Height: 0.2mm

Strength

Walls: 2
Top Shell Layers: 3
Bottom Shell Layers: 3
Infill: 10% (Gyroid)